Project description
Q1) You are asked to select materials for the manufacture of pistons fitted to a modern petrol engine car. The piston has to be able to withstand the conditions of the environment within which it operates.
State the selection criteria of the chosen materials taking into account the material properties, their cost and their suitability for manufacture.
Your answer must be supported by illustrations and test data sheets.
(maximum 350 words)
Q2) State the main properties of the materials used in the manufacture of:
1-Copper wire
2-Steel I section beams
3-The front stub axle of a car
4-A lathe high speed steel cutting tool
5-Electric heating element in an electric fire
6-Transformer core
Give detailed explanations of your answers and illustrate them with diagrams.
(maximum 1000 words)
Q3) Discuss any three microstructural characteristics (e.g. the grain size and shape or the phase structure) of the following:
a-Ceramics
b-Composite Materials
c-Polymers
d-Metals
The discussion must be limited to a maximum of 1000 words in total.
Q4) Discuss any three characteristics related to the macroscopic behaviour (e.g. chemical, physical or mechanical properties) of the four categories of materials mentioned previously in Q1
The discussion must be limited to a maximum of 1000 words in total
Q5)The following data is for cold-worked carbon steel tested in a tensile test:
Original diameter: 12.725 mm
Final diameter: 8.433 mm
Original gauge length: 50.8 mm
Final gauge length60.71 mm
Load
(kN)
0
5.5
11.7
17.0
22.1
27.4
40.5
53.1
60.5
64.7
66.9
68.7
70.5
71.5
72.1
72.8
Extension
(mm)
0
0.010
0.020
0.030
0.040
0.050
0.076
0.102
0.127
0.152
0.178
0.203
0.254
0.305
0.356
0.508
The maximum load was 74.3 KN. Plot the stress strain (Extension-Load) graph and determine:
a-Modulus of elasticity
b-Tensile strength
c-Percentage elongation
d-Percentage reduction in area
Q6) The following results were obtained from a tensile test of a polymer:
Load
(kN)
0.0
0.1
0.2
0.3
0.4
0.5
0.6
0.63
0.65
Extension
(mm)
0.0
0.08
0.17
0.35
0.59
0.88
1.33
2.00
2.40
The test piece had a width of 20 mm, a thickness of 3 mm and a gauge length of 80 mm. Plot the stress strain graph and determine:
a) Modulus of elasticity
b) Tensile strength
c) The ductility, in percent elongation
d) Yield strength at a strain offset of 0.002
You are required to comment on the values obtained in parts (a) and (b) for both questions and draw comparisons between the two values for both materials
Q7) 3.Search, look up and identify the suitable data (British Standards, International Standards, product data sheets, manufacturers literature, specification sheets, test data and engineering drawings) available for the manufacture of two engineering components of your choice. (a kitchen sink, a stainless steel adjustable spanner or the casing of a fire alarm control panel are just few examples of many such products).
The engineering products chosen must be able to be manufactured out of one of the following metal, ceramic, polymer and/or composites.
Provide at least three samples of the data obtained above and critically assess their reliability for use in the general world of materials engineering. (Maximum 150 words)

Are you looking for a similar paper or any other quality academic essay? Then look no further. Our research paper writing service is what you require. Our team of experienced writers is on standby to deliver to you an original paper as per your specified instructions with zero plagiarism guaranteed. This is the perfect way you can prepare your own unique academic paper and score the grades you deserve.
Use the order calculator below and get started! Contact our live support team for any assistance or inquiry.
[order_calculator]